Installing Arch Linux on a ThinkPad X40

From ThinkWiki
Jump to: navigation, search

Some notes to get Arch Linux running on a Thinkpad X40.

TODO
Not fnished yet. I'm documenting the installation process as it goes

Preface

I downloaded the FTP installation CD on http://www.archlinux.org/

Wireless

Atheros-based

My main concern was getting the WIFI to work. As the downloaded ISO also functions as a livecd, I tried to get it up and running with that. Without success. I found the answer to my question here: http://bbs.archlinux.org/viewtopic.php?pid=482359

I installed madwifi and madwifi-utils. In the modules section of /etc/rc.conf I banged the ath5k module, disabling it. With ath5k not banged the card showed up as wlan0, associated correctly with the AP, but didn't get a DHCP lease. Even with manually setting the IP and adding the default route, I couldn't ping the AP.

After banging ath5k, the wireless card shows up as ath0. Associating works, DHCP doesn't time out. :)

Intel PRO/Wireless 2200BG

dmesg should mention the ipw2200 card was detected. To get this running, you will need to do 

 # pacman -S ipw2200-fw

and add ipw2200 to the MODULES variable in your /etc/rc.conf. Reboot to get the module initialized.

Power Management

The two most important factors of a mobile device are battery life and weight. I'm always a bit disgrunted when an advertisement doesn't mention one or either.

Without any powersaving installations the 8cell battery still managed for a nice 4 hours.

CPU Frequency Scaling

CPU Frequency Scaling is a technology primarily for notebooks that enables the OS to scale the CPU speed to system and/or power use.

I simply followed the following instructions: http://wiki.archlinux.org/index.php/Cpufrequtils

Suspend

I tried pm-utils. 2 

 # pacman -S pm-utils

Add acpi_sleep=s3_bios to the file /boot/grub/menu.lst as kernel option.

I added following modules to the /etc/pm/config.d/config file in the order they are dependant of eachother. The last ones depend on the first modules. 

 SUSPEND_MODULES="wlan_wep wlan_scan_sta ath_rate_sample ath_pci wlan ath_hal"

But suspending seems to work even without this.

If the backlight is not working when resuming from suspend, the following might fix it [1]: 

 #!/bin/bash                                                                     
 case $1 in
   suspend)
       ;;
   resume)
       chvt 1
       vbetool post &
       sleep 1
       kill $!
       chvt 7
   ;;
 esac

Put the script in /etc/pm/sleep.d/. The changing of the virtual terminals with chvt is used to avoid a garbled screen after invoking vbetool in X.

Hibernate

To hibernate, you can simply use pm-utils too. It provides the pm-hibernate program. Only add the resume drive to the kernel line in /boot/grub/menu.lst: 

 resume=/dev/sda2

The drive assigned is the swap partition. The swap partition should be at least big enough to hold your RAM data.

I also needed to add the resume hook to the file /etc/mkinitcpio.conf [2]. Then recompile the kernel: 

 mkinitcpio -p kernel26

Enable suspend/hibernate buttons

To get the suspend keycombo (fn+f4 and fn+f12) to work, install xbindkeys: 

 # pacman -S xbindkeys

And place the following in ~/.xbindkeysrc 

 "sudo pm-suspend"
 c:223
 "sudo pm-hibernate"
 c:165

The keycode you can find out by running xev and looking for the appropriate keycode.

Adding xbindkeys to a startup script of your windowmanager makesthe keys active. As the name suggests, xbindkeys only works in X.

Xorg

Installed xorg with 

   # pacman -S xorg

Then generated the xorg.cong file with 

   # hwd -xa

(I know, risky ;))

Looked good, but X didn't start with this (couldn't find display). I installed the xf86-video-intel and changed the display driver from i810 to intel in /etc/X11/xorg.conf: 

   Section "Device"
           Identifier  "Card0"
           Driver      "intel"
           VendorName  "All"
           BoardName   "All"
   EndSection


Getting the back/forward special keys to work

Add the following to your ~/.Xmodmap 1 

   keycode 77 = Num_Lock
   keycode 234 = XF86Back
   keycode 233 = XF86Forward

Enabling scrolling with middle mouse button

Add the following to your /etc/X11/xorg.conf, to the PS/2 mouse section 1 

   Option "EmulateWheel" "true"
   Option "EmulateWheelButton" "2"

Postface

Don't forget to run [3] 

 # alsaconf

to get the sound to work properly.

FOOTNOTES [Δ]
Retrieved from "https://www.thinkwiki.org/w/index.php?title=Installing_Arch_Linux_on_a_ThinkPad_X40&oldid=48977"