Installing Debian 5.0 (Lenny) on a ThinkPad X200

Installation

This laptop is free from legacy devices such as CD/DVD so installation is a bit trickier than the average laptop. I first attempted to install using the Goodbye Microsoft installer from Vista. To get the menu visible in the Vista version I used I had to type this into a priviliged cmd.exe:

bcdedit.exe /timeout 5

A couple of reboots later I gave up on this method as the menu item refused to boot with the reason that it couldn't find the "\g2lbr.mbr" file, or that it might be corrupt. Before giving up I tried changing this path. This can be done by issuing:

bcdedit.exe 

This will print all the boot alternatives. You'll see a long id-hash associated with the Debian Installer. Grab that and go ahead with the next:

bcdedit.exe /set {the-long-id-hash} path WHAT-YOU-BELIVE-IS-CORRECT

I tried changing this to "c:\g2lbr.mbr" as that's where the file is located, but without any luck.

Next up.. I grabbed a legacy-device, USB DVD drive ;). Netinst went fine and after booting up the system I installed the 2.6.26 package from a USB stick and ethernet was up and running. I'm still fighting with X and wifi, so I'll update this page later.

Ethernet

Ethernet works after upgrading to version 2.6.26 of the Linux kernel.

[    1.533055] eth0: (PCI Express:2.5GB/s:Width x1) 00:1f:16:06:ee:ec
[    1.533055] eth0: Intel(R) PRO/1000 Network Connection
[    1.533055] eth0: MAC: 5, PHY: 8, PBA No: 1008ff-0ff

Trackpoint

The integrated orgasmic educator works out of the box. Haven't tried any PM yet but here's what the kernel has to say. The error might be caused by me not having any docking station, just a guess though.

[    8.516313] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[    8.536456] input: TPPS/2 IBM TrackPoint as /class/input/input9

Web Camera

The built-in webcam works out of the box.

[    8.004081] uvcvideo: Found UVC 1.00 device <unnamed> (17ef:480c)
[    8.004361] input: UVC Camera (17ef:480c) as /class/input/input8
[    8.010590] usbcore: registered new interface driver uvcvideo
[    8.010594] USB Video Class driver (v0.1.0)

ACPI Power Management

Haven't tried any PM yet but here's what the kernel has to say. The error might be caused by me not having any docking station, just a guess though.

[    7.610770] ACPI: \_SB_.PCI0.SATA.PRT1: found ejectable bay
[    7.610770] ACPI: \_SB_.PCI0.SATA.PRT1: Adding notify handler
[    7.610770] ACPI: Error installing bay notify handler
[    7.621495] thinkpad_acpi: ThinkPad ACPI Extras v0.20
[    7.621495] thinkpad_acpi: http://ibm-acpi.sf.net/
[    7.621495] thinkpad_acpi: ThinkPad BIOS 6DET28WW (1.05 ), EC 7XHT21WW-1.03
[    7.621495] thinkpad_acpi: Lenovo ThinkPad X200, model 74585MG
[    7.625495] thinkpad_acpi: radio switch found; radios are enabled
[    7.625495] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[    7.625495] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[    7.629495] Registered led device: tpacpi::thinklight
[    7.629495] Registered led device: tpacpi::power
[    7.629495] Registered led device: tpacpi:orange:batt
[    7.629495] Registered led device: tpacpi:green:batt
[    7.629495] Registered led device: tpacpi::dock_active
[    7.629495] Registered led device: tpacpi::bay_active
[    7.629495] Registered led device: tpacpi::dock_batt
[    7.629495] Registered led device: tpacpi::unknown_led
[    7.629495] Registered led device: tpacpi::standby

Suspend To RAM

Initial attepmts failed. Haven't investigated why yet.

Suspend To Disk

Works out of the box.