Intel Graphics Media Accelerator 950
Intel Graphics Media Accelerator 950This is an Intel video adapter Features
|
Two Drivers One Chip
There are two major version ranges of driver for this chipset: <2.0 and >2.0 correspondingly referred to as "i810" or "intel" under the "Device" section of xorg.conf. The newer driver supports dynamic configuration of display parameters including resolution, refresh rate, multiple monitor configuration, etc. through the xrandr command line utility without restarting the Xserver. Essentially, it strives to minimise the necessity of editing the xorg.conf file manually. It does not, however support the old "dual head" (non-xinerama) mode for multiple monitors. Thus, the older driver is better suited to those who prefer this configuration.
The newer "intel" driver
The newer driver is the one currently supported by Intel and for most cases, is the recommended one. It is extensively documented and available for download at http://intellinuxgraphics.org/. It is also likely to be available in the repository of your favourite distribution. Once installed, there should also be an "intel" manpage which has information about driver specific options in the xorg.conf file.
xorg.conf
The newer driver comes as a godsend to those who are tired of pulling their hair out over the infamous xorg.conf file. The developers at Intel have strived to downplay the role of this pesky config file as much as possible. The necessity for the "Server Layout" and "Monitor" sections was turfed entirely (though the latter may still be needed to properly configure multiple pointing devices), and the required lines in the "Device" and "Screen" are minimal. Thus, the basic working starting point for the sections relevant to graphics (excluding any manually loaded modules) is:
Section "Device"
Identifier "Intel Graphics Adapter"
Driver "intel"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Intel Graphics Adapter"
EndSection
With some possible embellishments, your distribution's automated installer should probably be able to figure this out for you. Resolution, refresh rate, etc will be auto-detected. If you don't like the auto-detected settings, you can use the XRandR command line utility to adjust them dynamically without having to restart the X server! You can always of course get more sophisticated with the xorg.conf file. Just type man intel or read Intel's documentation for more info.
External VGA port with XRandR
Unfortunately, given the radical changes to the role of the xorg.conf file, old dual-head xorg.conf files may not even allow the server to start! To remedy this, remove all the "ServerLayout" sections (or at least remove dual-head specific settings from them) and all but the main Screen section in xorg.conf. The latter should be made to look like the above with the addition of a "Display" subsection which specifies the upper bound of the total resolution spanned by the multi-monitor virtual screen. This is necessary because the default virtual screensize is 1280x1280 which is likely too small for any practical multi-monitor setup. If you just want to mirror the displays, this will happen automatically with the above described xorg.conf entries and you can skip this step. Please note that the videocard does not support DRI with virtual screen size larger than 2048x2048.
Section "Screen"
Identifier "Default Screen"
Device "Intel Graphics Adapter"
SubSection "Display"
Virtual 2048 2048
EndSubSection
EndSection
Once you have started X, you should find that your multiple monitors are automatically activated and mirror each other to the extent allowed by their potentially different geometries. If you want them to appear as a "large desktop", you need to adjust their relative position with the XRandR utility. You can get an idea of what you're working with by typing
xrandr -q
This will give you a list of outputs and tell you which ones are connected. The external vga port should be called "VGA" while the builtin LCD should be called "LVDS". If, for example you want to stack your desktops vertically, you might do something like
xrandr --output LVDS --below VGA
or
xrandr --output VGA --below LVDS
your window manager may treat the two cases differently in terms of where it decides to put things like the toolbar. Ideally, you probably want to put the desired xrandr command someplace that it might get executed before your window manager starts. For example in your ~/.xsession or ~/.xinitrc file.
External VGA port with xorg.conf
While XRandR eliminates the need to deal with xorg.conf in posititioning your screens, you may just want them to be laid out correctly from the outset. In this case, you can specify the default orientation of the displays in the xorg.conf file (which you can still change later with XRandR). This involves adding a "Monitor" section for each physical display output specifying its position. You must also tell the driver which "Monitor" belongs to which output (VGA,LVDS,etc) with the associated "monitor-..." option.
Section "Device"
Identifier "Intel 945GM"
Driver "intel"
Option "monitor-VGA" "External VGA"
Option "monitor-LVDS" "Builtin LCD"
EndSection
Section "Monitor"
Identifier "Builtin LCD"
Option "Below" "External VGA"
EndSection
Section "Monitor"
Identifier "External VGA"
Option "Above" "Builtin LCD"
EndSection
Section "Screen"
Identifier "Screen Dual"
Device "Intel 945GM"
SubSection "Display"
Virtual 2048 2048
EndSubSection
EndSection
More info can be found at http://www.intellinuxgraphics.org/dualhead.html
Old "i810" Driver
The old driver might be preferred by those who like the old style non-xinerama dual-head setup or for whatever reason can't get their hardware or software to work with the new driver. The old driver is currently still available in the repositories of many distributions.
Debian
For example 1.7.2-4 is the version used by Debian etch (stable), while the newer driver is available in the lenny (testing) and sid (unstable) repositories. If you have repositories for all three releases of Debian in your /etc/apt/sources.list file, you can specify the version to install using the -t option to apt-get/aptitude. To install the old driver,
aptitude install -t stable xserver-xorg-video-i810
As the package manager will try and replace the older driver during regular upgrades, the section of the apt-howto regarding package pinning may be relevant.
Fedora
In Fedora Core 5 at least, the i810 driver can be obtained from the updates (in updates-testing as of Aug 15, 2006). With that, the i810 driver seems to work.
Tweaks
To get a noticeable speedup in GLX/DRI try this in your xorg.conf (tested with the game Sauerbraten on a Z61e):
Section "Device"
Identifier "Intel Corporation Mobile Integrated Graphics Controller"
Driver "i810"
BusID "PCI:0:2:0"
VideoRAM 131072
Option "XAANoOffscreenPixmaps" "true"
Option "MTRR" "on"
Option "UseFBDev" "false"
Option "LinearAlloc" "6144"
Option "MonitorLayout" "CRT,LFP"
Option "DevicePresence" "true"
EndSection
External VGA port
Works. Dualhead is supported.
There are two options for running the external VGA port - either as a copy of the LCD (clone) or as a separate workspace. Here is an example for the separate workspace mode for xorg.conf for the X60s:
Section "Device"
Identifier "Intel Corporation Mobile Integrated Graphics Controller"
Driver "i810"
BusID "PCI:0:2:0"
Option "MonitorLayout" "CRT,LFP"
Option "DevicePresence" "true"
Screen 1
EndSection
Section "Device"
Identifier "Intel Corporation Mobile Integrated Graphics Controller External CRT"
Driver "i810"
BusID "PCI:0:2:0"
Screen 0
EndSection
Section "Monitor"
Identifier "LCD"
Option "DPMS"
EndSection
Section "Monitor"
Identifier "External CRT"
Option "DPMS"
HorizSync 28-75
VertRefresh 43-100
EndSection
Section "Screen"
Identifier "External Screen"
Device "Intel Corporation Mobile Integrated Graphics Controller External CRT"
Monitor "External CRT"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x1024"
EndSubSection
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Intel Corporation Mobile Integrated Graphics Controller"
Monitor "LCD"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1024x768"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Default Screen" 0 0
Screen 1 "External Screen" RightOf "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "Synaptics Touchpad"
EndSection
Did not work for me (FC6, x60s) but this one did: (as the x-server crashes at startup if the external port is the primary display you need to change the bios option BIOS>Config>Display>Boot Display Device to "ThinkPad LCD")
Section "ServerLayout" Identifier "Default Layout" Option "Xinerama" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" LeftOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "de" Option "XkbVariant" "nodeadkeys" EndSection Section "Monitor" Identifier "Monitor2" ModelName "Belinea 1905 G1" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "dpms" EndSection Section "Device" Identifier "Videocard0" Driver "i810" BusID "PCI:0:2:0" Option "MonitorLayout" "CRT,LFP" Option "DevicePresence" "true" Screen 0 EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "Device" Identifier "Videocard1" Driver "i810" BusID "PCI:0:2:0" Option "MonitorLayout" "CRT,LFP" Option "DevicePresence" "true" Screen 1 EndSection Section "Screen" Identifier "Screen1" Device "Videocard1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1280x1024" "1024x768" "800x600" "640x480" EndSubSection EndSection
Here is the relevant text for running the VGA port as a true clone (so even things like Xine video playback appears on both screens) of the internal LCD display:
Section "Device"
Identifier "Videocard0"
Driver "i810"
BusID "PCI:0:2:0"
Option "MonitorLayout" "NONE,LFP+CRT"
Option "DevicePresence" "true"
Option "CheckLid" "false"
VendorName "Lenovo"
BoardName "Intel Corporation Mobile Integrated Graphics Controller"
EndSection
915 Resolution
Default video modes does not support resolution 1400x1050. You can use 915resolution to change that.
# To show supported video modes: 915resolution -l # To add 1400x1050 support: 915resolution 5a 1400 1050 # You may need to specify 24-bit color: 915resolution 38 1400 1050 24
Xorg will be able to use this resolution after that.
Quirks
I had to disable dri and glx because of X11 crashes with programs using 3D. see http://ubuntuforums.org/showthread.php?t=289763
VESA (console) resolution
Largest video resolution, supported by VESA for T60 is 1280x1024. You can set that for console in grub or lilo by adding vga=794 option.
SVideo port
??
DVI port
DVI passthrough is only supported on the T60.
Suspend behaviour
- Required kernel parameters for suspend to ram: none
- Additional notes:
- switch to/from X11 to reinitialize display properly (stays black)
- DO NOT use vbetool to save/restore the video mode, this breakes resume!
