IrDA

From ThinkWiki
Revision as of 03:16, 12 June 2005 by Tonko (Talk | contribs) (→‎Supported Models)
Jump to: navigation, search

ThinkPad IrDA configuration

IrDA can be used to communicate using Infrared to other IrDA compliant devices, such as other Notebooks, PDA's and mobile phones.

All IBM ThinkPads manufactured in the last years have integrated IrDA that can be used in one of two modes, SIR or FIR. Some very old ThinkPads only support SIR mode, or might not have IrDA support at all.

The purpose of this document is to get the IrDA hardware in your ThinkPad operational, setting up communication to other devices is not covered. However, the external links section can prove useful for this.

Serial IR (SIR)

SIR is limited to serial datarates up to 115.2Kb/s

Linux 2.4 kernel config

Edit /etc/modules.conf and add the following lines 

  alias tty-ldisc-11 irtty
  alias char-major-161 ircomm-tty

Fast IR (FIR)

FIR is the preferred mode of IrDA operation and operates at a bandwidth of 4 Mbps

Main problem here is that the chips FIR mode needs to be activated. On A, G, R, T and X model ThinkPads, the easiest way to activate FIR mode is by entering BIOS setup during boot-up by pressing F1 when prompted. Then, selecting 'Config' followed by 'Infrared' will allow you to control the IrDA operation. Here you will need to select the option to Enable the infra-red port. Be sure to save the changes, and then Exit.

Note: Changing these BIOS settings do not affect Windows 2000 or XP operating systems, but may cause memory resource issues in older windows versions, or other legacy operating systems.

If changing the BIOS setting is not an option or if the settings cannot be altered, as on some older ThinkPads, the FIR mode can be activated by running Linux OS with one of the following:

  • setpnp as part of the old pcmcia-utils source package
  • tpctl, but only for some old ThinkPads

If the FIR mode is not activated, attempts to load the nsc-ircc module will result in an error in syslog of "Wrong chip version ff".

Linux 2.4 kernel config

Edit /etc/modules.conf and add the following lines 

      alias irda0 nsc-ircc
      options nsc-ircc dongle_id=0x09 io=0x2f8 irq=3
      pre-install nsc-ircc setserial /dev/ttyS1 uart none port 0 irq 0

Linux 2.6 kernel config

Edit /etc/modprobe.conf and add the following lines 

      alias irda0 nsc-ircc
      options nsc-ircc dongle_id=0x09 io=0x2f8 irq=3
      install nsc-ircc /bin/setserial /dev/ttyS1 uart none port 0 irq 0; /sbin/modprobe --ignore-install nsc-ircc

If you have a Thinkpad R51-1830WCZ infrared might not work though. You need a pnp version of the nsc-ircc driver. There exists a patch for the standard nsc-ircc driver from Jean Tourrilhes. It enables the device and probes it afterwards. You still have to call setserial and set the dongle_id parameter manually. With this driver it "works for me" (only SIR tested) but the driver needs to be reloaded after a suspend to S3 state.

Get the patch here: link nsc-ircc-pnp.diff it applied cleanly against 2.6.10. An updated version for 2.6.12-rc6 can be found here: nsc-ircc-pnp.2.6.12-rc6.diff.

Very Fast IR (VFIR)

A newer VFIR standard exists, which supports speeds upto 16Mbps.
However for the moment no ThinkPads support this.

Some other things you might want to do with IrDA

  1. add fast PPP support:

modprobe irnet

  1. if needed, limit further the size of the transmit window

echo 1 > /proc/sys/net/irda/max_tx_window

External links

Linux-IrDA Project (External)

Linux PCMCIA Project (External)

tpctl homepage (External)

Supported Models

IrDA 1.0 (SIR - 115Kbps)

IrDA 1.1 (FIR - 4Mbps)

Retrieved from "https://www.thinkwiki.org/w/index.php?title=IrDA&oldid=5650"