Talk:How to hotswap Ultrabay devices
Contents
HAL script
If the script works, your lshal output should contain something similar to this. In this case the Ultrabay device was a second HDD (/dev/sdb).
Note that in the example, storage.hotpluggable = true while before it was false, so the script worked.
udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_HTS726060M9AT00_MRH453M4H11ARB'
block.device = '/dev/sdb' (string)
block.is_volume = false (bool)
block.major = 8 (0x8) (int)
block.minor = 16 (0x10) (int)
block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SATA_HTS726060M9AT00_MRH453M4H11ARB' (string)
info.capabilities = {'storage', 'block'} (string list)
info.category = 'storage' (string)
info.parent = '/org/freedesktop/Hal/devices/pci_8086_24ca_scsi_host_0_scsi_device_lun0' (string)
info.product = 'HTS726060M9AT00' (string)
info.udi = '/org/freedesktop/Hal/devices/storage_serial_SATA_HTS726060M9AT00_MRH453M4H11ARB' (string)
info.vendor = 'ATA' (string)
linux.hotplug_type = 3 (0x3) (int)
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host1/target1:0:0/1:0:0:0/block/sdb' (string)
storage.automount_enabled_hint = true (bool)
storage.bus = 'pci' (string)
storage.drive_type = 'disk' (string)
storage.firmware_version = 'MH4O' (string)
storage.hotpluggable = true (bool)
storage.lun = 0 (0x0) (int)
storage.media_check_enabled = false (bool)
storage.model = 'HTS726060M9AT00' (string)
storage.no_partitions_hint = false (bool)
storage.originating_device = '/org/freedesktop/Hal/devices/computer' (string)
storage.partitioning_scheme = 'mbr' (string)
storage.removable = false (bool)
storage.removable.media_available = true (bool)
storage.removable.media_size = 60011642880 (0xdf8f90000) (uint64)
storage.requires_eject = false (bool)
storage.serial = 'SATA_HTS726060M9AT00_MRH453M4H11ARB' (string)
storage.size = 60011642880 (0xdf8f90000) (uint64)
storage.vendor = 'ATA' (string)
| ID | ThinkPad model | South Bridge chip (for Ultrabay) | parent device (host_0, lun0 = 2nd ATA controller, master device) |
|---|---|---|---|
| 8086_7111 | T20, T21, T22, X20, X21 | Intel 82371AB/EB/MB PIIX4 IDE | /org/freedesktop/Hal/devices/pci_8086_7111_scsi_host_0_scsi_device_lun0 |
| 8086_248a | T23, T30, X22, X23, X24, X30 | Intel 82801CAM IDE U100 (rev 2) | /org/freedesktop/Hal/devices/pci_8086_248a_scsi_host_0_scsi_device_lun0 |
| 8086_248a | A30, A30p | Intel 82801CAM IDE U100 (rev 2) | /org/freedesktop/Hal/devices/pci_8086_248a_scsi_host_scsi_device_lun0_0 /org/freedesktop/Hal/devices/pci_8086_248a_scsi_host_0_scsi_device_lun0 |
| 8086_24ca | R50, R51, T40, T40p, T41, T41p, T42, T42p, X31, X32, X40 | Intel 82801DBM (ICH4-M) | /org/freedesktop/Hal/devices/pci_8086_24ca_scsi_host_0_scsi_device_lun0 |
| 8086_2653 | R52, T43, T43p, X41, Z60m, Z60t | Intel 82801FBM (ICH6-M) | /org/freedesktop/Hal/devices/pci_8086_2653_scsi_host_scsi_device_lun0 |
| 8086_27c4 | R60, X60 | Intel 82801GBM (ICH7 Family) | /org/freedesktop/Hal/devices/pci_8086_27c4_scsi_host_scsi_device_lun0 |
| 8086_27df | T60, T60p, Z61m, Z61t, Z61p | Intel 82801GBM/GHM (ICH7 Family) | /org/freedesktop/Hal/devices/pci_8086_27df_scsi_host_scsi_device_lun0 |
| 8086_2850 | R61, T61, T61p, X300 | Intel 82801H (ICH8 Family) | /org/freedesktop/Hal/devices/pci_8086_2850_scsi_host_scsi_device_lun0 |
| 8086_2929 | R400, R500, T400, T500, W500, W700, X200, X301 | Intel 82801I ICH9 Family | /org/freedesktop/Hal/devices/pci_8086_2929_scsi_host_0_scsi_device_lun0 |
lshal output
Please place your lshal output here if you had problems, or if you have a A or W series ThinkPad
lshal of my A31: http://nopaste.org/p/a4p6x9tSob
Thanks! If I understand the output correctly you have one Toshiba Combo DVD-ROM/CD-RW R2002 in one ultrabay connected as slave to the primary IDE controller, and one Toshiba DVD-ROM C2512 in the second ultrabay connected as master to the secondary IDE controller. Can you confirm? I have added it to the table.
bash script for hotswapping UltraBay
Here is my script for hotswapping ultrabay, is more complex, supports swap partition on drive in ultrabay, check holders (useful, when you are using luks) and more :)
ultrabay.sh
#!/bin/bash
SCSI_DEVICE=""
FORCE_SLEEP="1"
QUIET="0"
SYSLOG="0"
BEEP="0"
Message()
{
MESSAGE="${0/*\//}: $*"
if [ "$QUIET" = "0" ]; then
echo "$MESSAGE"
fi
if [ "$SYSLOG" != "0" ]; then
/usr/bin/logger "$MESSAGE"
fi
true
}
Exit()
{
case "$1" in
"fail")
[ $BEEP != "0" ] && echo 2 > /proc/acpi/ibm/beep
exit 1
;;
"success")
[ $BEEP != "0" ] && echo 12 > /proc/acpi/ibm/beep
exit 0
;;
esac
}
Usage()
{
echo "usage: ${0/*\/} [options]"
echo "options:"
echo " -d <path> SCSI device (required)"
echo " -s Ignore fail when putting drive to sleep"
echo " -q No messages"
echo " -l Use syslog for messages (-q has no effect)"
echo " -b Use beep for notification (-q has no effect)"
exit 1
}
Block2Device()
{
/bin/readlink -e "/dev/block/$1"
}
IsSwap()
{
/sbin/swapon -s | grep -q -e "^$1\b"
}
IsMounted()
{
mount | grep -q -e "^$1\b"
}
HasHolders()
{
[ "$(ls "$1/holders")" ]
}
IsBusy()
{
DEVICE=$(Block2Device $(cat "$1/dev"))
if IsSwap "$DEVICE" || IsMounted "$DEVICE" || HasHolders "$1"; then
Message "device '$DEVICE' is busy"
false
else
true
fi
}
SleepDrive()
{
BLOCK=$(cat $SCSI_DEVICE/block/*/dev 2> /dev/null)
DEVICE=$(Block2Device "$BLOCK")
if ! /sbin/hdparm -Y "$DEVICE" &> /dev/null; then
Message "cannot put drive to sleep"
if [ $FORCE_SLEEP = "0" ]; then
true
else
false
fi
fi
}
DeleteScsiDevice()
{
if ! { echo 1 > $SCSI_DEVICE/delete; } &> /dev/null; then
Message "cannot delete device"
false
fi
}
GetDock()
{
grep "$1" /sys/devices/platform/dock.*/type | sed -e s%/type:.*%%
}
IsDocked()
{
[ $(cat $(GetDock "$1")/docked) -ne 0 ]
}
Undock()
{
{ echo 0 > $(GetDock "$1")/undock; } &> /dev/null
if IsDocked "$1"; then
Message "cannot undock UltraBay"
false
else
Message "UltraBay undocked"
true
fi
}
while getopts "d:qlsb" OPTION; do
case $OPTION in
d)
SCSI_DEVICE="$OPTARG"
;;
s)
FORCE_SLEEP="0"
;;
q)
QUIET="1"
;;
l)
SYSLOG="1"
;;
b)
BEEP="1"
;;
?)
Usage
;;
esac
done
if [ -d "$SCSI_DEVICE" ] && IsDocked "ata_bay"; then
sync
for DEV_DIR in $(ls $SCSI_DEVICE/block/*/*/dev $SCSI_DEVICE/block/*/dev | sed -e s/dev$// 2> /dev/null); do
IsBusy "$DEV_DIR" || Exit "fail"
done
sync
SleepDrive || Exit "fail"
DeleteScsiDevice || Exit "fail"
sleep 4
fi
if [ ! -d $SCSI_DEVICE ] && $(IsDocked "ata_bay"); then
if Undock "ata_bay"; then
Exit "success"
else
Exit "fail"
fi
fi
Message "UltraBay is already undocked"
Exit "success"
Supported models: R400 - linux-2.6.29
comments
Interesting, especially the support for swap partitions. but I have two comments, first your calling your script hotswap.sh and then having udev call ultrabay.sh?
Then your hard coding the location of the Ultrabay device. This is not guaranteed to be correct, although it will be in most cases. In particular the A and W-series machines. A-series had support for more then one Ultrabay device, while W-series has support for more then one internal HDD in addition to the Ultrabay device, so the Ultrabay location will shift. That is why the Ultrabay Eject script on the main page gets the eject device information from udev.
comments
Hi, thanks, I fix name of script :) Udev calling ultrabay.sh with option -d, so it remove correct device, if you want remove device manualy, is default device useful. But option may be required...
more comments ;)
You might also have a look at the script on the main page, it has a few extra abilities, such as logging to syslog, beeping and putting up popups on the desktop.
Logging to syslog is simple, just call 'logger' with what you want to log. quite should have no effect on this.
For beeps, similar to what windows does you can echo different values to /proc/acpi/ibm/beep, but it only works if sound is not muted. Unfortunately doing so does seem to generate some annoying messages in syslog.
Lastly you can use notify-send to put up messages on the desktop, but before you can do so you have to do an export DISPLADISPLAY=0:0 /usr/bin/knotify4 --passive-popup : Adresář nebo soubor neexistujeY=:0.0
Syslog and beep
OK, scrip now support syslog and beeping :).
Still missing notify-send ;)
I am also thinking that it would be useful in the case of a busy filesystem to tell the user to run something like fuser -mv /dev/sr0
Or perhaps we should run it ourselves automatically and just tell the user what is the cause of the busy filesystem.
--Tonko 21:21, 8 June 2009 (UTC)
